⚙️ **ABSOLUTE vs INCREMENTAL ENCODERS — WHAT'S THE DIFFERENCE?**
Both measure rotation, but they tell your control system different things.
🟠 **Absolute encoder**
Provides a position value for the shaft.
A single-turn version identifies its angle within one revolution, while a multi-turn version can also track revolutions.
It's particularly useful when equipment needs to recover its position after power is restored.
🔵 **Incremental encoder**
Produces pulses as the shaft rotates.
By counting pulses, the controller can measure movement and speed. With two quadrature channels (A and B), it can also determine direction.
But if the controller loses its position count during a power failure, it may need a reference or homing operation before accurate positioning can resume.
**The key difference?**
Absolute tells you *where you are*. Incremental tells you *how far you've moved*.
Neither is automatically better. It depends on what the machine needs to know.
**Which do you encounter more often — absolute or incremental encoders?**
#Spannero #IndustrialAutomation #Encoders #PLC #MaintenanceEngineering
## Absolute vs Incremental Encoders: How Do They Work?
Rotary encoders are used in industrial automation to measure shaft movement, speed and position. They provide feedback to PLCs, drives and motion controllers, helping machines monitor and control mechanical movement.
Although absolute and incremental encoders can look similar, they provide different types of information.
### Absolute Encoders
An absolute encoder provides a position value corresponding to the shaft's angular position.
**Single-turn absolute encoders** identify the shaft angle within one complete revolution.
**Multi-turn absolute encoders** can additionally track the number of revolutions, within their specified range.
A key advantage is that an absolute encoder can provide position information after power is restored, without needing to count all the movements made since a reference point.
However, this does not automatically establish the machine's mechanical reference. Correct installation, calibration and configuration remain important.
Absolute encoders are commonly used in robotics, indexing equipment, servo systems and positioning applications.
### Incremental Encoders
Incremental encoders generate pulses as the shaft rotates.
A controller counts these pulses to determine relative movement and can calculate speed from the pulse rate.
Many incremental encoders provide two output channels, A and B, with a phase difference of approximately 90 electrical degrees. This arrangement, known as quadrature, allows the controller to determine rotation direction.
Some also provide a Z channel, producing a reference pulse once per revolution.
Incremental encoders are commonly used for conveyors, packaging machinery, motor feedback and movement measurement.
### What Happens After a Power Failure?
An absolute encoder can report its position when power returns, subject to its design and operating limits.
An incremental encoder normally cannot recover a lost position count from its pulse outputs alone.
If the machine needs a known absolute position, a homing or reference procedure may therefore be required.
However, applications that only need speed feedback or relative movement do not necessarily require homing.
### Which Encoder Should You Choose?
Choose an **absolute encoder** when knowing the shaft position immediately is important, especially where recovering position after a power interruption matters.
Choose an **incremental encoder** when pulse counting, relative movement, speed or direction feedback meets the application's requirements.
Other factors include resolution, interface compatibility, operating environment, mechanical mounting and overall system cost.
**Spannero Workshop Tip:** When troubleshooting an encoder fault, check the encoder type, supply voltage, output signals, coupling condition and controller configuration before assuming the encoder itself has failed.
## Troubleshooting encoder problems without guessing
An encoder-related alarm does not necessarily mean the encoder has failed. The problem can be mechanical, electrical or in the controller's interpretation of the signal.
### Start with the machine's observation
Record the exact alarm, whether position or speed feedback is missing, and whether the fault occurs continuously or only during movement. Check recent work on couplings, cables, drives and control parameters.
### Mechanical checks
With the equipment safely isolated and any stored movement energy controlled, inspect the encoder mounting and shaft coupling. A loose coupling can produce incorrect position feedback even when the electronics are functioning. Check for damage or signs of slipping; do not turn a machine axis manually unless the equipment procedure permits it.
### Electrical and signal checks
Use the encoder datasheet and wiring diagram to identify the correct supply, common, signal type and connector pinout. Incremental outputs may be push-pull, open collector or differential; absolute encoders may use serial or industrial network interfaces. The right test depends on the actual device and controller. Do not connect a generic test instrument to unknown pins or assume all encoder signals are 24 V.
### Incremental encoder symptoms
Missing A or B pulses can cause counting or direction errors. Noise, damaged cable shielding, loose connectors and incorrect input configuration can also cause intermittent faults. A reference Z pulse is not a substitute for a complete homing strategy.
### Absolute encoder symptoms
Check communications status, device addressing where applicable, configuration and the relationship between the encoder's reported value and the machine's mechanical reference. A valid absolute position value does not prove that the machine is correctly calibrated.
## Quick comparison
| Question | Absolute | Incremental |
|---|---|---|
| What does it report? | Position within its defined range | Pulses representing relative movement |
| Does the controller normally need to count motion to establish position? | No, subject to system design | Yes |
| Can it provide speed feedback? | Often, through successive position readings | Yes, from pulse timing or count rate |
| Is homing always required after power loss? | Not necessarily | Depends on whether absolute machine position is required |
**Workshop takeaway:** Verify the mechanical connection, correct electrical interface and controller configuration before condemning an encoder. Follow the machine's safe isolation and authorised diagnostic procedures.

