🏭 **FASTER MACHINES, MORE PROBLEMS?**
Management wants another 10% production.
Simple solution?
Turn the speed up!
Except now the conveyor keeps jamming, sensors are missing products, rejects are increasing and maintenance is being called every twenty minutes.
Sound familiar?
**HERE'S THE PROBLEM...**
Running a machine faster doesn't automatically mean producing more.
Sometimes it means producing more faults.
⚙️ **WHAT CAN HAPPEN WHEN SPEED INCREASES?**
🔸 **Less time for sensors** — Products may pass through detection zones more quickly, exposing timing or response limitations.
🔸 **More demanding transfers** — Products can become unstable or collide at conveyors and transfer points.
🔸 **More mechanical stress** — Higher acceleration, forces and cycling rates can expose wear or design limitations.
🔸 **More rejects** — Processes may struggle to maintain quality at higher speeds.
🔸 **More frequent stoppages** — Small faults can wipe out the gains from running faster.
**THE REAL QUESTION ISN'T HOW FAST THE MACHINE CAN RUN.**
It's how many good products it can produce over an entire shift.
A machine running steadily at 90% of its maximum rate might outperform one running flat out but constantly stopping.
And that doesn't mean slower is always better.
If a machine can run faster reliably, without compromising quality or safety, that's genuine improvement.
**WORKSHOP TIP 🔧**
Before increasing production speed, establish the current losses.
Are you limited by the machine, the material, the process or something further down the production line?
Don't automatically blame the machine when the problem could be elsewhere.
💬 **What's your experience? Does increasing machine speed improve production, or just give maintenance more work?**
**spannero | For people who like to know how things work.**
## Why Faster Doesn't Always Mean More Productive
In manufacturing, increasing machine speed seems like an obvious way to improve production.
If a machine produces 100 parts per minute, increasing its speed to 110 parts per minute should theoretically increase output by 10%.
But there's a catch.
That calculation assumes the equipment continues operating reliably and produces the same proportion of acceptable parts.
In reality, increased speed can expose weaknesses elsewhere in the production process.
## 1. Sensors and Timing
Many automated machines rely on precisely timed signals from proximity sensors, photoelectric sensors, encoders and other devices.
As operating speed increases, the available time for detection and response may decrease.
Consider a photoelectric sensor detecting products on a fast-moving conveyor.
If product spacing or detection time becomes too small for the sensing and control arrangement, the machine may experience missed detections or incorrect sequencing.
Other possible limitations include:
- PLC scan times and filtering settings
- Sensor response times
- Actuator reaction times
- Mechanical positioning accuracy
- Communication and control delays
The correct response is to identify the actual limitation, not simply remove filtering or bypass interlocks to make the machine operate faster.
## 2. Mechanical Forces and Wear
Increasing operating speed can also increase mechanical demands.
Depending on the equipment, this may involve:
- Higher acceleration and deceleration forces
- Increased vibration
- Greater impact forces at transfer points
- Reduced settling time
- More operating cycles per hour
- Additional bearing, belt or drivetrain loading
These effects depend on the design and operating conditions.
A machine designed and maintained for higher speeds may cope perfectly well. Another machine may already be operating close to its practical limits.
## 3. Product Handling Problems
This is particularly relevant to high-volume manufacturing.
An individual machine might be capable of operating faster, while the equipment around it struggles to keep up.
Examples include:
- Containers becoming unstable on conveyors
- Products colliding at transfer points
- Inadequate separation between products
- Accumulation systems reaching capacity
- Downstream machinery failing to accept products quickly enough
Increasing the speed of one machine may simply transfer the problem to another part of the production line.
The limiting factor is often the overall process, not the fastest individual machine.
## 4. Quality Losses
Production speed must remain compatible with the manufacturing process.
For example, reducing cycle time may affect cooling, heating, forming or other process conditions.
A faster cycle that increases rejects or produces unstable products may reduce the number of acceptable units leaving the factory.
The objective should be to increase the rate of good production, not simply the number of machine cycles.
## 5. The Difference Between Speed and Output
Consider two hypothetical production scenarios.
**Machine A — Stable operation**
- Running speed: 100 parts per minute
- Availability: 95%
- Good-product rate while running: 98%
- Good products in an eight-hour shift: 44,688
**Machine B — Increased speed**
- Running speed: 110 parts per minute
- Availability: 80%
- Good-product rate while running: 95%
- Good products in an eight-hour shift: 40,128
Machine B runs 10% faster when operating.
Yet it produces 4,560 fewer good products over the shift.
These figures are illustrative, not measurements from a real factory. They assume constant running rates and an eight-hour planned production period.
The lesson is that additional downtime and quality losses can outweigh the benefits of increased running speed.
## 6. Understanding OEE
Overall Equipment Effectiveness, or OEE, combines three measures:
**Availability** — How much of the planned production time the equipment is running.
**Performance** — How its actual production compares with the ideal production rate.
**Quality** — What proportion of its output meets the required quality standard first time.
OEE = Availability × Performance × Quality
Improving machine speed can increase the Performance component, provided the ideal-cycle-time reference is defined correctly.
But if increased speed causes more downtime or rejects, Availability and Quality may fall.
That's why looking at speed alone can be misleading.
## 7. A Better Way to Increase Production
Before turning up the speed, ask:
**Where is production actually being lost?**
Investigate the largest recurring losses first.
For example:
- Frequent short stoppages
- Product jams
- Recurring sensor faults
- Poor changeovers
- Mechanical failures
- Quality rejects
- Downstream bottlenecks
A machine running below its maximum design speed isn't automatically inefficient.
Equally, lowering speed isn't a substitute for fixing equipment that should be capable of operating faster.
A controlled speed trial can be useful when authorised, within validated equipment and process limits, and supported by appropriate monitoring.
Compare good output, downtime, rejects and recurring faults before and after the change.
## The Engineering Lesson
The aim of a production line is not to make machinery move as quickly as possible.
It's to produce the required quantity of acceptable products safely, reliably and efficiently.
Sometimes higher speed delivers that.
Sometimes improving reliability, product handling or process stability produces a much greater benefit.
**The best operating speed is the one that delivers the best sustainable production performance — not necessarily the highest number on the HMI.**

